About Fluid-Based (Hydronic) Systems
The core difference between fluid-based and air-based systems is the medium.
Water carries roughly 3,500 times more heat per unit volume than air. A ¾" pipe can move about as much heat as a duct several hundred times its cross-section, and pumps use far less energy than fans to move it.
Air systems, however, are the only practical way to deliver ventilation, filtration, and dehumidification.
So the real design question is usually not which medium to use, but how to divide the work between them.
‣
Fluid-Based (hydronic) System Options
- Radiant floors: PEX tubing in a slab, gypcrete, or panels under the floor finish. Low water temperature, typically 85–120°F for heating.
- Radiant ceilings or walls: embedded tubing or metal panels. These can heat and, with care, cool.
- Radiators and baseboard:
- Traditional cast-iron or fin-tube units run at 140–180°F.
- Modern panel radiators are sized for low-temperature water, around 110–130°F.
- Chilled beams: passive (convection only) or active (induced by ducted primary air). Mainly for cooling.
- Fan coils: a hybrid that uses hydronic heat transport but delivers heat to the room through a small fan and air coil.
‣
Pros and Cons
Radiant floor / surfaces | Radiators / baseboard | Ducted air | |
Comfort | Excellent: even temperature, warm surfaces, no drafts, minimal stratification | Very good; some convective draft and warm spots near units | Fair to good; drafts, noise, and stratification if poorly designed |
Response time | Slow (hours) for slabs; faster for thin panels | Moderate | Fast (minutes) |
Cooling | Possible, but limited by condensation (surfaces must stay above dew point) and capacity (~10–15 Btu/h·ft² floors) | Not practical | Yes, the standard choice |
Dehumidification | None | None | Yes, at the coil |
Ventilation and filtration | None, needs a separate DOAS or ERV | None | Built in |
Transport energy | Very low (pumps) | Very low | Higher (fans), plus duct leakage and heat loss |
Fit with heat pumps / condensing boilers | Excellent: low supply temperatures boost efficiency | Good with low-temp panels; poor with legacy high-temp units | Good with heat pumps |
Space needs | Invisible; needs floor buildup and manifold closets | Wall space under windows | Large shafts, soffits, ceiling plenums |
Noise | Silent | Silent, or minor ticking | Fan and air noise |
Indoor air quality | Doesn't stir dust or allergens | Mild convection | Can spread dust, odors, and contaminants; helps if well filtered |
Zoning | Easy, with a loop per room | Easy, using thermostatic radiator valves | Harder: needs dampers, VAV, or multiple units |
First cost | High | Moderate | Lowest when cooling and ventilation are needed anyway |
Maintenance / risk | Hidden leaks are costly; tubing is long-lived | Low; bleeding air, occasional valve service | Filters, belts, duct cleaning; failures are easy to reach |
Flexibility for renovation | Poor once installed in a slab | Good | Good, if ducts are accessible |
‣
Additional Factors to Consider
- Hydronic-only buildings still need air. Modern codes require mechanical ventilation, and humid climates need dehumidification. A radiant or radiator building almost always also has a DOAS or ERV with small ducts. The real comparison is usually "hydronic plus small ventilation ducts" versus "all-air."
- Radiant cooling is easy to get wrong. Without tight dew-point control (supply water around 60–65°F, plus dew-point sensors and dehumidified ventilation air), surfaces sweat. It works well in dry climates like Phoenix, and well in humid climates only when paired with a strong DOAS.
- Slab thermal mass works in both directions. It smooths out temperature swings and pairs well with time-of-use rates or steady heat-pump operation. It also handles fast load changes poorly: sun on large windows, a room filling with people, or night setbacks. It can overshoot.
- Water temperature drives plant efficiency. Low-temperature emitters (radiant floors, oversized panel radiators) let heat pumps and condensing boilers run at their best. Legacy high-temperature radiators often force a boiler, or require oversized replacements during electrification retrofits.
- Ducts lose energy quietly. Leaky ducts in attics or other unconditioned spaces can waste 20–30% of delivered energy in residences. Hydronic piping losses are much easier to contain.
‣
Recommendations by use case
‣
- Cold-climate homes with good envelopes, especially slab-on-grade or basements
- Spaces with high ceilings or large volumes, where ducted heat would stratify: lobbies, atriums, churches, gyms, airport halls, museums
- Garages, warehouses, workshops, vehicle bays (heat stays at floor level and recovers fast after doors open)
- Bathrooms and kitchens, where warm floors are a comfort upgrade
- Heat-pump or geothermal projects that want the lowest possible supply water temperatures
- Hospitals and healthcare spaces where draft-free, quiet, low-dust conditions matter
‣
- Dry climates, or buildings with a strong DOAS handling all latent load
- Offices, labs, and schools with steady sensible loads and good solar control
‣
- Retrofits of existing hydronic buildings: older homes, apartments, schools
- Projects that want room-by-room control at moderate cost
- Heating-dominant climates where cooling is minor or handled separately (by ductless mini-splits, for example)
- Electrification upgrades, using low-temperature panel radiators sized for heat pumps
‣
- Commercial offices, labs, and hotels that want hydronic efficiency with ceiling space at a premium
- Buildings where ventilation volume is small compared with the cooling load
‣
- Hot or humid climates where cooling and dehumidification dominate (the U.S. Sun Belt, including Arizona)
- Spaces with high or variable ventilation needs: classrooms, auditoriums, retail, restaurants, conference centers
- Buildings that need filtration or pressure control: cleanrooms, isolation rooms, data centers, labs
- Budget-driven projects where cooling is required anyway, so one system does everything
- Spaces with fast-changing loads, intermittent occupancy, or frequent reconfiguration
‣
- Radiant floors or radiators for heating, plus a ducted DOAS or ERV for ventilation and a mini-split or ducted heat pump for cooling
- DOAS combined with radiant panels, chilled beams, or fan coils. This decouples ventilation from thermal conditioning, shrinks duct sizes dramatically, and often cuts fan energy by half or more compared with all-air VAV
General Guidance
- Use water to move heat and air to move air.
- Size the ductwork for ventilation and humidity control, and let a hydronic system handle the thermal load wherever budget, climate, and building type allow.
- Use an all-air system when cooling and latent loads dominate, ventilation rates are high, or first cost is the main constraint.
Videos
‣
Mindmap
Click the left or right arrows at the bottom of the mindmap to step thru the slideshow.